[shippingguy]

With the stock wheels I did my calipers black, but since I changed the wheels the black was not doing it. Had to switch up the color. Much better matches all the accents on the car now.

[SSShark]

Originally Posted by shippingguy

With the stock wheels I did my calipers black, but since I changed the wheels the black was not doing it. Had to switch up the color. Much better matches all the accents on the car now.

Those calipers came out amazing! Excellent work. What did you use to paint them?

[ZPirate]

Very nice! I should do mine.

[shippingguy]

Originally Posted by SSShark

Those calipers came out amazing! Excellent work. What did you use to paint them?

I have a guy out here in CA that does them. He uses VHT High Temp Caliper paint, but it’s all in the process and application. He preps(sands), primers, paints and does multiple clear coats OVER the decals so they are protected. Takes him around 5 hours. I’ll ceramic coat them myself this week.

[SnakeEyeSS]

Using the Ctek that came with the ZL1 (part of the dealer order) to charge my dying Accord battery.

For the second time, a separate Schumacher battery charger with automatic maintain mode once charged failed to maintain. I trashed my last one because I figured I had dropped it too many times. This one is older but wasn't used much, and a bigger, higher quality one with 80 amp start mode(think it was $140 10 years ago, got it cheap at sears clearance ), and again, it charged to 100% and then seemed to just kill the battery. It said 12.5 volts and 100% charge, I reset it and it immediately read 11.1 volts and 10% charged(confirmed with my voltmeter). So I do not recommend the Schumacher speedchargers. Mine had an 80 amp(start), 20 amp(charge), 10 amp and 2 amp mode. My kill a watt shows it was drawing 100 watts in its failed maintain mode, so if you have one, I wouldn't trust it. Had the same thing happen with an old 20 amp max one.

I have a noco 1 amp on each Camaro, but thinking about the 4 or 6 amp gooloo maintainer for my daily since they don't have as much down time.to be refreshed

[SSShark]

Originally Posted by shippingguy

I have a guy out here in CA that does them. He uses VHT High Temp Caliper paint, but it’s all in the process and application. He preps(sands), primers, paints and does multiple clear coats OVER the decals so they are protected. Takes him around 5 hours. I’ll ceramic coat them myself this week.

He does excellent work. They look like factory!

[KC64]

Very nice! Those look SHOW CAR ready!

[beowulf556]

Hardwired a radar detector and dash cam with the gen5diy kit. Works great.

[truckrglenn]

I replaced the driver side wiper insert with a new one. What a pain, I had to use my knife to extend the channels in the rubber on both ends so that I could slide it on, then put on the end caps.

Only paid $10 for the insert and 5 minutes of my time.

[LT1Zob]

Found a good deal on an OE front splitter off a rear ended totaled 23. Now I’m really done. Lol

[cman2270]

72,000 mile checkup the past few days:
-Replaced rotors & pads for the first time since new
-Replaced cabin air filter
-Replaced main filter
-Replaced wipers w/ some Bosch Icons - so far W wipers
-New full set of tires are here ready to go on after the summer
-Detailed the outside to enjoy cars & coffee this morning

[LT1Zob]

Originally Posted by cman2270

72,000 mile checkup the past few days:
-Replaced rotors & pads for the first time since new
-Replaced cabin air filter
-Replaced main filter
-Replaced wipers w/ some Bosch Icons - so far W wipers
-New full set of tires are here ready to go on after the summer
-Detailed the outside to enjoy cars & coffee this morning

Well done. And welcome. Great 1st post. Now for some pics of your car